Today I’m going to step you through putting a newer version of Node JS on your LinkIt Smart 7688. The default version of node available is 0.12.7 which, let’s face it, is completely outdated and essentially useless for to any serious Node.js developers. Now there are some ongoing challenges with putting a completely up to date version of Node on the MIPS architecture. This is because there are key libraries needed to build Node JS that are not updated on MIPS yet… so since those libraries out out of date we can only get so far.
Setup your linux machine.
I use Ubuntu server 16.04.2 LTS at the time of writing this tutorial. Get Virtual Box, download an Ubunut 16 .ISO, create a new VM, make sure your disk is around 50GB (5GB is not enough… found this out the hard way), select the ISO you downloaded, install the operating system (be sure to add SSH for convenience).
I alway use SSH for copy paste commands. To setup you VM so you can ssh to it:
- Open the setting for the VM (you can do this while its running)
- Go to Network > Adapter 1 > Advanced > Port Forwarding
- Forward 127.0.0.1:2200 to 10.0.2.15:22
- Check your ifconfig to verify your VMs IP address
SSH to it from your host with this:
ssh email@example.com -p 2200
Alternatively you can put the adapter in Bridge mode… then check ifconfig for the VMs IP.
Setup for the build
Following for guide here with modified instruction for things they forgot:
and with help from the nxhack who is running this repo:
- Add the python package (if you didn’t install during Ubuntu OS install)
sudo add-apt-repository ppa:fkrull/deadsnakes sudo apt-get update
- Install prerequisite packages to build the firmware:
sudo apt-get install git g++ libncurses5-dev subversion libssl-dev gawk libxml-parser-perl unzip wget build-essential python2.7
- Download the OpenWrt CC source codes:
git clone git://git.openwrt.org/15.05/openwrt.git
- Prepare the default configuration file for feeds:
cd openwrt cp feeds.conf.default feeds.conf
- Add the LinkIt Smart 7688 development board’s and NodeJS to the builds feed:
sudo nano ./feeds.conf
Add the following lines to the bottom of the file:
src-git linkit https://github.com/MediaTek-Labs/linkit-smart-7688-feed.git
src-git node https://github.com/nxhack/openwrt-node-packages.git;for-15.05
- Update the feed information for all available packages to build the firmware:
- Change the packages installed as default:
wget https://gist.githubusercontent.com/nxhack/7ced4d866a59ebc72737589b49a220f8/raw/1bebfe9f6091f55a5856bc4af00da456a4995b09/mtk-linkit.patch patch -p1 < mtk-linkit.patch
- Fix build error of depend on node.js version:
wget https://gist.githubusercontent.com/nxhack/4357d51918ba8f3cb5cc00080ad0815c/raw/e96758224ade8cb224523aedf5ea3249a6a59425/MRAA.patch patch -p1 < MRAA.patch
- Hack for wifi driver so build completes
Copy kernel objects for support kernel 3.18.45:
see : MediaTek-Labs/linkit-smart-7688-feed#37
cp ./feeds/linkit/mtk-sdk-wifi/wifi_binary/mt_wifi.ko_3.18.44 ./feeds/linkit/mtk-sdk-wifi/wifi_binary/mt_wifi.ko_3.18.45 cp ./feeds/linkit/mtk-sdk-wifi/wifi_binary/mt_wifi.ko_3.18.44_all ./feeds/linkit/mtk-sdk-wifi/wifi_binary/mt_wifi.ko_3.18.45_all
- Install all packages:
./scripts/feeds install -a
- Use node.js custom packages:
rm ./package/feeds/packages/node rm ./package/feeds/packages/node-arduino-firmata rm ./package/feeds/packages/node-cylon rm ./package/feeds/packages/node-hid rm ./package/feeds/packages/node-serialport ./scripts/feeds install -a -p node
- Prepare the kernel configuration:
- Select the following options:
- Target System: Ralink RT288x/RT3xxx
- Subtarget: MT7688 based boards
- Target Profile: LinkIt7688
- (Optional) GO into Languages > Node.js > Configuration (under the node package) > Select your desired version.
- (Optional) Enable modules you want (Caution there is a 30MB limit so not all will fit)
- (Recommended) node-npm (it is a separate module in v6)
- Save and exit (use the default configuration file without any modification)
- Select the following options:
- !!!BEFORE YOU START!!!
RUN THIS FROM YOUR VM NOT OVER SSH
This command will take a while and if your ssh pipe breaks so will your build
Start the compilation process:
There are several options you can use with the make command that are helpful.
– V=99 (gives verbose output during build) or
– V=1 (shows error, warnings, and notes “less verbose”)
– &> output.log ( on the end – stores output in a log for later viewing)
A Few Hours Later…
- After the build process is finished successfully, the resulted firmware file will be under “bin/ramips/openwrt-ramips-mt7688-LinkIt7688-squashfs-sysupgrade.bin”. If its’ not there check the output in your log file or on your screen. Depending on the hardware resources of the host environment, the build process may take more than 2 hours.
- You can use this file to update the firmware through Web UI or rename it to lks7688.img to update through a USB drive.
A big thanks to nxhack for making this build possible!
Download images for the version of Node you want: